AEN.TECH

Request A Quote

Now ask about our full range of products and services.

  • nickname:

  • mailbox:

  • content:

Pneumatic soft seal butterfly valve

28 Apr 2018 21:38:00 source:aen-valve.com browse:7689
  • Introduction
  • Technical Parameters

Overview of pneumatic hard seal butterfly valve products

The pneumatic soft seal butterfly valve manufactured by tech consists of angle stroke piston pneumatic actuators, rubber seal butterfly valve, carbon steel or stainless steel valve plate and valve stem. Pneumatic soft seal butterfly valves are used as regulating flow and intercepting medium in water supply and drainage and gas pipelines with temperature less than or equal to 120 ℃ such as food, medicine, chemical industry, petroleum, electric power, light textile, paper making, etc. The main characteristics of pneumatic soft seal butterfly valve are:

( 1 ) the design is novel, reasonable, unique in structure, light in weight, and quick in opening and closing.

( 2 ) the operating torque is small, the operation is convenient, labor-saving and dexterous.

( 3 ) it can be installed at any location and is convenient to maintain.

( 4 ) the seal can be replaced, and the sealing performance can reliably reach zero leakage of the bidirectional seal.

( 5 ) the sealing material has the characteristics of aging resistance, corrosion resistance, long service life and the like.

Technical parameters of pneumatic soft seal butterfly valve
Nominal path DN ( mm ) DN50~1000mm
Nominal pressure ( MPa ) PN1.0、1.6、2.5MPa
Valve body form Through cast valve body
Connection form Flange type, opposite clip type
Valve core form Butterfly plate
gasket Ding Qing oil-resistant rubber: within 80 degrees of temperature resistance; PTFE: temperature resistance within 130 degrees
intrinsic error With positioner: less than 2 % of total travel
return difference With positioner: less than 2 % of total travel
Control mode Switch type ( switch two-position control ), regulating type ( 4 ~ 20ma control )
Configuration actuator model Gt, at, aw series single and double acting pneumatic actuators
Technical parameters of pneumatic clamp butterfly valve actuator
Actuator model Gt, at, aw series single and double acting pneumatic actuators
Supply pressure 0.4~0.7MPa
Air source interface G1/4"、G1/8"、G3/8"、G1/2"
Ambient temperature -30~+70℃
Action form Single-acting actuator, double-acting actuator
Accessory Positioner, solenoid valve, air filter pressure reducer, retaining valve, travel switch, valve position transmitter, handwheel mechanism, etc.

It adopts a new type of pneumatic actuators, with double-acting and single-acting ( spring return ), rack and pinion drive, safe and reliable. Large diameter valves adopt series aw type pneumatic actuators fork-pull transmission, with reasonable structure, large output force, double-acting type and single-acting type.

1. gear type double piston, with large output torque and small volume.

2. the cylinder is made of aluminum-gold material, which is light in weight and beautiful in appearance.

3. manual operating mechanisms can be installed at the top and bottom.

4. rack type connection can adjust opening angle and rated flow.

5. the actuator can select live signal feedback instructions and accessories to realize automatic operation.

6. is 05211 standard connection provides convenience for installation and replacement of products.

7. the adjustable joint screws at both ends can make the standard product have an adjustable range of 4 between 0 and 90. Ensure the synchronization accuracy with the valve.

Material of main parts of pneumatic soft seal butterfly valve
Name Main materials
body Ductile cast steel, cast steel, alloy steel, stainless steel
plate Gray cast iron, ductile cast steel, cast steel, stainless steel and special materials
Seal ring Various rubbers, PTFE
stem 2cr13, stainless steel
packing O - ring, teflon ring
Main performance specifications for pneumatic soft seal butterfly valves
Nominal diameter DN(mm) 50~1000
Nominal pressure PN(MPa) 0.6 1.0 1.6
test pressure
Applicable medium
Driving form
strength test 0.9 1.5 2.4
pressure test 0.66 1.1 1.76
Gas seal test 0.6 0.6 0.6
Nominal diameter Air, water, sewage, steam, gas, oil, etc.
Nominal pressure pneumatic actuator
Sealing material and applicable temperature of pneumatic soft sealing butterfly valve
Material variety Neoprene Nitrile
rubber
EPR PTFE Silicone
rubber
Fluorine
rubber
Natural
rubber
Nylon
English
abbreviations
CR NBR EPDM PTFE SI VITON NR PA
Model code X or J XA or JA XB or JB F or XC、JC XD or JD XE or JE X1 N
Maximum
temperature
resistance
82℃ 93℃ 150℃ 232℃ 250℃ 204℃ 85℃ 93℃
Minimum
temperature
resistance
-40℃ -40℃ -40℃ -268℃ -70℃ -23℃ -20℃ -73℃
Applicable operating
temperature
0~+80℃ -20~+82℃ -40~+125℃ -30~+150℃ -70~+150℃ -23~+150℃ -20~+85℃ -30~+93℃

Product selection of pneumatic soft seal butterfly valve

( 1 ) valve body parameters: nominal diameter, working pressure, process medium, use occasion, valve body material and other series of parameters.

( 2 ) actuator parameters: actuator form, control mode, control signal ( 4 - 20ma, 1 - 5v ), action mode ( air - open, air - closed )

Try to provide the technical parameters of pneumatic soft seal butterfly valve in detail so as to facilitate our company's operation and technical personnel to select the right type for you. If you have any questions, you can call us and we will do our best to provide you with quality service!

Previous:
Next:pneumatic hard seal butterfly valve